Guide alphabétique, de la thermodynamique, amplification de chaleur, transfert de masse, et dynamique des fluides
Français À propos Comité de rédaction Contactez-nous Accès Begell House

In heat storage, use is made of the thermal capacity of solid or liquid materials, either by their sensible (specific) heat effect (heating/cooling cycles) or by their latent heat effect at a phase change (melting/freezing cycles). For heat storage, the important thermal characteristics are:

1. Heat capacity. MJ/m3

2. Charge and discharge rates, CP (Ti − T0), kW/m3

3. Heat loss rate , kW/m3

4. Thermal stratification, ΔTSTR

Heat Capacity

When use is made of the sensible heat effect a high volumetric specific heat (ρcp) of the material is required. Table 1 gives some data for typical materials. Solid materials are often used in rock (packed) beds. As packing densities are often between 60% and 85% the volumetric capacity (ρcp) is reduced proportionally. For higher temperatures the use of such packed beds as regenerators is common. For low temperature applications like home heating and solar energy, water storage is mostly used.

In latent heat stores the latent heat effect is important. At the phase change temperature the heat of solidification will be available when freezing a liquid. Table 2 gives some latent heat effects and the solidification temperature Ts for several materials. For some organic materials, there is a transition range ΔTtr . Inorganic materials may show supercooling effects, which means that the heat discharges at a (unwanted) lower temperature. Also segregation can occur in inorganic solutions in water.

Charge and Discharge Rates

To load/unload a heat storage vessel a heat transfer fluid (like water, air, oil) takes up the heat either by direct contact or through a heat exchanger. Often the limiting heat transfer is on the heat storage material side. Conductivity (λ) in solid materials limits the heat transfer rate. In Table 1 a typical discharge time τ based on transient heat conduction problem for a Fourier number Fo = æτ/d2 equal to 0.5 has been given for a typical dimension d of 10 mm (see Fourier Number). The time τ gives the time for a 90% or more completed loading/unloading cycle. It increases proportional to d2. Also for the solidification (unloading) part of a latent heat store this is the limiting heat transfer mechanism. For liquid heat stores and in melting, natural convection effects will increase the heat transfer rate. For organic latent heat materials with low conductivity-values finned pipes and embedded metal structures are used to improve the heat transfer.

Heat Loss Rate

Heat losses of the storage vessel to the surroundings can severely diminish the heat storage efficiency.

Thermal Stratification

In sensible heat stores the heat is loaded/unloaded in an axial direction. In this direction, a temperature gradient (ΔTSTR) will occur. In the optimal case, there is a rather sharp temperature front. However, due to axial dispersion of heat, and in liquids also due to convection flows, this front will be spread out. With large convection flows it can even completely disappear and result in a single, mixed temperature. Due to the dispersion the average temperature in the storage at the end of the loading will decrease. This lowers the storage efficiency.

Table 1. Sensible heat storage properties

Table 2. Latent heat storage properties

REFERENCES

Hoogendoorn, C. J. and Bart, G. C. J. (1992) Performance and modelling of lat. heat stores, Solar Energy, 48, 1, 53-58.

Ouden, C. den (1981) Thermal Storage of Solar Energy, Martinus Nijhoff Publishers, the Hague, NL.

Paykoc, E. and Kakac, S. (1987) Solar Thermal Energy Storage; in Solar Energy Utilization, H. Yüncü , Ed., NATO ASI Series, Martinus Nijhoff Publishers, Dordr., NL.

References

1. Hoogendoorn, C. J. and Bart, G. C. J. (1992) Performance and modelling of lat. heat stores, Solar Energy, 48, 1, 53-58.
2. Ouden, C. den (1981) Thermal Storage of Solar Energy, Martinus Nijhoff Publishers, the Hague, NL.
3. Paykoc, E. and Kakac, S. (1987) Solar Thermal Energy Storage; in Solar Energy Utilization, H. YÃ¼ncÃ¼ , Ed., NATO ASI Series, Martinus Nijhoff Publishers, Dordr., NL.
Nombre de vues : 41961 Article ajouté : 2 February 2011 Dernière modification de l'article : 14 February 2011 © Copyright 2010-2021 Retour en haut de page